2 X 1000 W  CERWIN-VEGA PA KABIN

Dual 15" 2-way Full Range Speaker
(Preliminary specifications subject to change.)

Featuring Cerwin-Vega’s HighRoad horn and two 15-inch woofers with 2.5-inch high temperature voice coils, the 252 is an 4-ohm, 2-way passive bass reflex design. Providing the flexibility to be used stand-alone, arrayed, or in conjunction with the 118S subwoofer, the 252 is rated at 1000 watts with a frequency response of 45Hz to 20kHz.

* Frequency Response: 45 Hz - 20 kHz
* Peak Power Handling: 1000 watts
* Program Power Handling: 500 watts       
* Nominal Impedance: 4 Ohms
* Sensitivity (1w/1m): 100 dB
* Connections: 2 x 1/4" Phone, 2 x Neutrik Speakon       
* Low Frequency: Dual 15" Woofers with 2.5" Voice Coil       
* High Frequency: 34mm Titanium Compression Driver with Exclusive Cerwin-Vega! HighRoad Horn
DYNACORD POWER MIXER 1600 MATE   2x500W

12 Mic Line/4Mic/stereo/Line, 2 neue Stereo Effekte,2 AUX. Feedback Filter..., Gewicht: 23.50 kg
Herstellertext:
Was macht einen PowerMate zum PowerMate?
Alle Funktionsgruppen eines PowerMate sind 100% professionell in Design und Ausstattung. Das beginnt beim Mischerteil mit höchstwertigem, diskret aufgebautem Mikrofon-Preamp, neuen, staubgeschützten ALPS-Fadern (speziell für PowerMate entwickelt) mit sehr hoher Dämpfung auch im HF-Bereich, 48V Phantom-Power in Sechsergruppen schaltbar und einer Dynamik, die vielen professionellen Mischpulten gut zu Gesicht stünde. AUX 3+4 sind getrennt Pre/Post schaltbar. Die Endstufen sind in hocheffizientem Class-H Design ausgeführt und leisten jetzt 2 x 700 W / 4 Ohm (PM 1000 und 1600). Sie verfügen über dynamische Limiter, ein umfassendes Schutzschaltungspaket und die patentierten LPN-Filter für deutlich verbesserte...
M-AUDIO DELTA 10/10 LT

8 x 8 unbalanced analog I/O
1 x 1 MIDI I/O
word clock I/O for sample accurate device synchronization
S/PDIF digital I/O with PCM and AC-3/DTS surround
2 mic preamps or line inputs
S/PDIF digital I/O (coaxial) with 2-channel PCM
SCMS copy protection control
digital I/O supports surround-encoded AC-3 and DTS pass-through
1 x 1 MIDI I/O
directly drive up to 7.1 surround (bass management software included)
software controlled 36-bit internal DSP digital mixing/routing

TRUTH B2031 BEHRINGER REFERANCE MONITOR

B2031 has become a favorite among musicians and engineers the world over for every imaginable application. Its neutral sound and extremely linear frequency response, optimized via manual trimming, assist you in getting the most out of your sounds, whether you’re recording, sampling, mixing or mastering. The low- and high frequency amplifiers deliver plenty of power for the specially developed heavy-duty 8 3 /4 " polycarbonate woofer and ferrofluid-cooled HF driver. The unique wave guide developed by our CAD engineers delivers absolutely linear phase response and optimal stereo imaging, giving the TRUTH monitor an unusually large sweet spot.
Adjustable low-frequency roll-off, high-frequency adaptation and a four-way room compensation allow optimal adaptation to any listening situation. Selectable power mode, high- and low-frequency mute functions, balanced XLR and 1 /4 " connectors, power and clip indicators, full electromagnetic shielding and a sturdy, low-vibration MDF enclosure round out this professional and unusually flexible monitor system.

FEATURES       
Extremely linear frequency response from 50 Hz to 21 kHz
Two high-power amps with 150 and 75 Watts
8 3 /4 " long-throw polycarbonate woofer
1" HF driver with ferrofluid-cooled aluminum dome
Integrated 2-band limiter for effective overload protection
Phase-optimized wave guide for controlled dispersion pattern and extremely large sweet spot
Flexible frequency and room acoustics adaptation
Full electromagnetic shielding
Sold in hand-matched pairs       

SPECIFICATION

Audio Inputs      
XLR                                   servo-balanced input
1/4" jack                            servo-balanced input
Impedance                         20kOhms
Max input level                   +22 dBu

Loudspeaker
Tweter                                25 mm ferrofluid-cooled dome
Woofer                               22 cm (8 3/4") polycarbonate diaghragm

Amplifiers
Low frequency                     max. 150 watts
High frequency                    max.  75 watts
Noise (SPL @ 10 cm)          <10 dBA @ 1 m (each)  

Crossover
Type                                    active, 4 th order Linkwitz-Riley filter
Crossover frequency              2 kHz

System specifications
Bandwidth                              50Hz to 21 kHz
Sound pressure level               max. 116 dB SPL @ 1 m (pair)
Marshall AVT100
100W 1x12 3-Kanal Combo DFX Amfi
Marshall AVT100X, 100W gücünde 30 cm hoparlöre sahip 3 kanall? bir amfidir. Sahip oldu?u 3 lambal? kanal sayesinde mümkün olan en geni? tonajlama elde edilmi?tir; temiz ve parlak clean tonlardan inan?lmaz sert tonlara kadar tüm beklentilerinizi kar??layacak bir amfi! 16 özel dijital efekti sadece 3 dü?me ile ayarlanabilir "Mix, Adjust, Select" 4 yollu LED pedal? sayesinde tonlar aras?nda kolayl?kla geçi? yapabilir veya efektleri aç?p kapatabilirsiniz. Kulakl?k ç?k???, speaker-emulated line out ve effects loop özelli?i bulunan AVT100X, tüm AVT serileri gibi 12AX7 ile donat?lm??t?r.
Marshall AVT100X 100W 1x12 3-Kanal Combo Amfi (DFX):
  
    * 100W give you the lethal force missile
    * 3 adet pedal ile de?i?tirilebilir kanal
    * Basit kullan?ma sahip 16 adet özel dijital efekt
    * 8 ohm empedans
    * Boyutlar : 60 x 52 x 30 cm
    * A??rl?k: 24,5 kg
    * Footcontroller: PEDL-10030

150 Watt Combo w/Reverb 2 x 12

- 150 Watts with 2 x 12" Speakers
- Two Discreet Channels
- 2 Separate 3 Band Active Eqs. with Parametric Midrange in Second Channel
- Normal Channel w/Switchable Overdrive
- Hot Channel w/Switchable Boost
- Gain and Volume Controls Each Channel
- Reverb and Resonance
- 1/4" CD/MP3 Input Jack
- 1/4" Headphones/Record Out Jack
- Channel, Reverb, Overdrive and Boost Footswitch Jacks
- Closed Back
- LED Indicator for Channel, Reverb, Overdrive and Boost - Effect Loop - 26.4"W x 19.5"H x 10.9"D - Weight: 71lbs.

Fender Rumble 100 Bass Combo Specifications:
* 21"W x 25"H x 13"D
* 60 lbs.
Fender Rumble 100 Bass Combo Features:
* Ported bass design
* 100W
* 15" special driver and piezo horn
* Carpet-covered cab
* Oversized corners
* Metal grille
* 4-band EQ
* Mid scoop switch
* Effects loop
* XLR line out
* CD input
* 4-band EQ

FENDER JAM 75 W USA
reverb, tremola,2 clean
2 distorsion

FENDER CHAMP 20 W USA LAMB
DUAL DIAPHRAGM CONDENSER MICROPHONE B-2 PRO
Gold-Sputtered Large Dual-Diaphragm Studio Condenser Microphone
The B-2 PRO is a high-performance dual-diaphragm studio condenser microphone. Vocalists and recording studio owners will be amazed by its uncompromising audio performance and features such as the additional low cut filter. The B-2 PRO provides a slightly pronounced 12 kHz range, producing the kind of "presence" that often eliminates the need for high-frequency EQing that would raise the overall noise floor. The B-2 PRO provides that much-desired transparency that can only be found on high-end large-diaphragm condenser mics. Key features include selectable cardioid, omnidirectional or figure-eight directivity pattern. The low-cut filter removes distracting low-frequency sounds, and built-in shielding minimizes high-frequency interference. A 10 dB attenuator can be used with high volume signal sources. The microphone is delivered in a rugged hard case with a suspension mount and a windscreen.

Professional 1" dual-diaphragm condenser microphone for unsurpassed audio quality
Ideal as main and support microphone for studio and live applications
Pressure-gradient transducer with shock-mounted gold-sputtered dual-diaphragm capsule
Exceptionally flat frequency response and incredible musicality
Selectable cardioid, omnidirectional or figure eight pickup pattern
Switchable low-frequency roll-off
Switchable input attenuation of -10 dB
Ultra low-noise transformerless FET input circuitry
Gold-plated 3-pin XLR output connector
Rugged construction with satin nickel-plated brass body
Heavy-duty suspension mount, windscreen and aluminum transport case included

SM58 Vocal Microphone
The Shure SM58® unidirectional (cardioid) dynamic vocal microphone is designed for professional vocal use in live performance, sound reinforcement,
and studio recording. It has a tailored vocal response for a sound which is a world standard for singing or speech. A highly effective, built-in spherical
filter minimizes wind and breath "pop" noise. A cardioid pickup pattern isolates the main sound source while minimizing unwanted background noise.

Type
Dynamic (moving coil)






Frequency Response
50 to 15,000 Hz
Polar Pattern
Unidirectional (cardioid), rotationally symmetrical about microphone axis, uniform with frequency
Sensitivity (at 1,000 Hz Open Circuit Voltage)  -54.5 dBV/Pa (1.85 mV) 1 Pa = 94 dB SPL
Impedance
Rated impedance is 150 ohms (300 ohms actual) for connection to microphone inputs rated low impedance
Polarity
Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3
Connector
Three-pin professional audio connector (male XLR type)
Net Weight 298 grams (10.5 oz)

SM57 Instrument Microphone
The legendary Shure SM57 microphone is exceptional for musical instrument pickup and vocals. With its bright, clean sound and contoured frequency response, the SM57 is ideal for live sound reinforcement and recording. It has an extremely effective cardioid pickup pattern which isolates the main sound source while minimizing background noise. In the studio, it is excellent for recording drums, guitar, and woodwinds.
The SM57's outstanding performance, legendary reliability, and diversity of application make this "workhorse" the choice of performers, producers, and sound engineers worldwide.

Type Dynamic
Frequency Response 40 to 15,000 Hz





Polar Pattern
Unidirectional (cardioid), rotationally symmetrical about microphone axis, uniform with frequency.
Sensitivity (at 1,000 Hz) Open Circuit Voltage: -56.0 dBV/Pa* (1.6 mV)  *(1 Pa = 94 dB SPL)
Impedance
Rated impedance is 150 ohms (310 ohms actual) for connection to microphone inputs rated low impedance.
Polarity
Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3.
Connector
Three-pin professional audio connector (male XLR type).
Net Weight (without cable) 284 grams (10 oz)

PG48 Vocal Microphone
An excellent performance microphone for spoken word applications.
The PG48-QTR includes a 15 ft (4.57m) XLR to 1/4" Cable, Microphone Clip, 5/8" to 3/8" Thread Adapter, and a Storage Bag.
The PG48-XLR includes a 15 ft (4.57m) XLR to XLR Cable, Microphone Clip, 5/8" to 3/8" Thread Adapter, and a Storage Bag.

Microphone Type Dynamic (moving coil)
Polar Pattern Cardioid (unidirectional)
    
   
    


Frequency, Response 70 to 15,000 Hz
Polarity, Positive pressure on diaphragm produces positive voltage on pin 2 rela-tive to pin 3 of microphone output connector
Output Impedance (at 1000 Hz) 600 ohms
Sensitivity (at 1000 Hz) -52 dBV/Pa, (2.5 mV), 1 Pascal = 94 dB SPL
Electromagnetic Hum Sensitivity 22 dB equivalent SPL in a 1 millioersted field (60 Hz)
Switch, Built-in On/Off switch
Connector,Three-pin professional audio connector (male XLR type)

PG58 Vocal Microphone
A rugged microphone tuned to accentuate the clarity of lead and back-up vocals.
* PG58-QTR includes a 15ft (4.57m) XLR to 1/4" Cable, Microphone Clip, 5/8" to 3/8" Thread Adapter, and a Storage Bag.
* PG58-XLR includes a 15ft (4.57m) XLR to XLR Cable, Microphone Clip, 5/8" to 3/8" Thread Adapter, and Storage Bag.
Microphone Type Dynamic (moving coil)
Polar Pattern  Cardioid (unidirectional)
    




Frequency Response  60 to 15,000 Hz
Polarity
Positive pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of microphone output connector
Output Impedance (at 1000 Hz) 300 ohms
Sensitivity (at 1000 Hz)  -53 dBV/Pa, (2.2 mV), 1 Pascal=94 dB SPL
Electromagnetic Hum Sensitivity  26 dB equivalent SPL in a 1 millioersted field (60 Hz)
Switch Built-in On/Off switch
Connector Three-pin professional audio connector (male XLR type)

AKG TPS D 3700/D 3700 S
(Discontinued)

# Frequency response optimized for vocal use
# Hypercardioid polar pattern for high gain before feedback
# Transducer protected by integrated dual protective basket

Rugged construction, distinctive Tri-Power styling, and outstanding sonic performance for vocalists on a budget. The D 3700 features an extended frequency response with a slight boost between 3 kHz and 15 kHz to project vocals out in front of dense mixes. Based on AKG know-how, the D 3700 combines a high-output Maximum Flux neodymium/iron-boron transducer and a uniform hypercardioid polar pattern to allow close-up work near high-level monitors without feedback. The smoothly triangulated PowerGrip body balances perfectly in the hand and the rugged body with Iso-Damp internal suspension guarantees reliability under the most severe touring conditions. The built-in windscreen removes easily for cleaning with a twist of the locking bayonet mounted grill. The D 3700 S is identical to the D 3700 except for the addition of a noiseless, recessed on/off switch.
D 3700 WL 1: D 3700 microphone element with threaded connection for use with various AKG WMS handheld transmitters.

SPECIFICATION
Polar pattern        hypercardioid
Frequency range        60 to 18,000 Hz at 1 cm (0.4 in.): 20 to 18,000 Hz
Sensitivity        2,5 mV/Pa (-52 dBV)
Max. SPL        147/156 dB (for 1% / 3% THD)
Equivalent noise level        22 dB-A
Impedance        600 ohms
Connector        3-pin XLR
Finish        matte black
Net weight        240 g / 8.5 oz.
Shipping weight        640 g / 1.4 lbs.

AV-JEFE   AVL2500
Specifications:

    * Element: Moving coil dynamic
    * Polar Pattern: Uni-directional
    * Frequency: 60 Hz - 16 KHz
    * Sensitivity:
           o -72 dB +- 3 dB (0 dB = 1V / microbar
1,000 Hz indicated by open circuit)
    * Output Impedance: 250 Ohm +- 30% (at 1KHz)
    * S / N Ratio: Over 65 dB
    * Material: Zinc die-cast
    * Dimensions:
          o AVL2500...£p52 x 186.4 mm
          o AVL2600...£p52 x 177.5 mm

Features:

    * Captures voice with outstanding clarity and excellent feedback rejection
    * High sound pressure tolerance low sensitivity to control breathing and pop noises
    * Rugged shock-mount system for reduced handling and cable noise
    * Slender probe design for maximum control and ease of handling
    * Built-in on/off switch
    * Rubberized shock rings on handle and mesh grille for protection against bumps and careless handling
    * Integrated multi-layer breath/wind filter in a hardened mesh grille
    * Durable all-metal case with non-glare gray finish
    * Sample Purchase: 5pcs

ZOOM 707 II
  
* 74 Different Effect Types, 10 Effects Simultaneously
      The 707II offers 74 different effects, available within eight effect modules,compatible to latest guitar sounds.

8 EFFECT MODULES
Booster        Amplifies the input signal to get an overdrive sound
Isolator / Compressor        Adjust the dynamics of a specific portion of a tone, or the entire bandwidth of the tone
Drive        Pick from several different distortion effects
Four band EQ        Boost or cut four frequency ranges-High, Mid-High, Mid and Low
Noise reduction        Includes Zoom Noise Reduction (ZNR) and a Noise-Gate
Cabinet        Cabinet simulator reproduces the tone of all the great cabinets
Modulation        A variety of effects like Chorus, Phase, Pitch-shift, Flange, Wah and more
Delay / Reverb        Produces several classic ambient effects

Enlargement,click here

    * 30 Types of Drive Sounds + 3 Types of Acoustic Simulation
      Thanks to the use of a VAMS(Variable Architecture Modeling System), the drive module contains 10 "personalities" including amplifier modeling. Each personality has 3 styles: Classic, Standard and Modern. Therefore, a total of 30 types of drive sounds are available. Using a dedicated Drive knob and Variation buttons, you can select and change the drive sound anytime. While in Play mode, parameter edit knob #1 is assigned to be the Drive Gain, so that you can adjust the amount of distortion. The drive module also has three Acoustic Simulations, so you can get acoustic tones on your favorite electric axe.

    * 120 Kinds of Practical Patches
      By combining effects and settings for each parameter, the user can create, edit and store 60 patches. Together with the 60 pre-set patches, a total of 120 patches are available. The Foot Switch can be used to change patches instantly. Using the patch swap function, you can easily arrange patch sequence to match the playlist of a live performance.

    * 3 Analog Knobs Offer Easy Editing
      When you want to change or create effects, 3 parameters can be modified at once using the analog knobs. You can independently adjust multiple parameters that affect each other, such as the Gain/Tone/Level of the Drive, the Speed/Depth/Mix of the Chorus, or Time/Tone/Mix of the Reverb, simultaneously. While in Play mode these 3 knobs are assigned as follows: 1.Drive gain, 2.Main modulation parameter, 3.Mix balance of Reverb/Delay. You can fine tune these to match any performance condition.

    * Built-in Expression Pedal
      An expression pedal is built-in. Using a dedicated pedal assignment key, you can easily change its function anytime. Also, different settings for each patch can be checked by looking at the LED indicators. You can adjust and store minmum and maximum value for each patch using the expression pedal for wah-wah, volume, or speed.

PEDAL FUNCTIONS
Pedal wah-wah
Pedal pitch shift
Speed or Depth parameter
Drive gain
Mix balance of Delay or Reverb
Master volume
Turn the sampler function ON/OFF

    * Designed For Live Performance
      Zoom's live performance design philosophy is featured at every critical point. The 707II features a large display for patch names, numbers and banks, that is highly visible on a dark stage. Extremely portable, compact, and light-weight the 707II has a dual power supply system for batteries or AC power, a low power consumption circuit that allows for 11 hours of use on alkaline batteries, and easy-to-read auto chromatic tuner.

    * Drum Machine Function
      60 different rhythm patterns are included. They cover a wide variety of genres, from basic 8- and 16-count beats, to pop and dance rhythms. Inheriting the drum machine technology of our popular RhythmTrak Series, the PCM sound makes it possible to practice using real drum sounds, not just a metronome.

    * Sampler Function
      Up to 6 seconds of your favorite guitar so unds or musical phrases can be sampled through the AUX IN. Using an optional 32 MB Smart Media card, the sampling time can be expanded to 8 minutes. Using a foot pedal, sampled sounds can be played once, or looped indefinitely. Built-in data storage is 16 bit un-compressed high quality sound. You can slow down the re-play speed of a sample up to 25 percent without changing the pitch--excellent for phrase training.

    * Patch-Sync Function
      60 effect patches can be linked with 60 drum patterns, and 60 files of sampled sound. You can perform highly sophisticated playing techniques with simple operations, such as changing effects and drum patterns together while playing, or re-playing different sampled sounds with each patch.

    * Using Smart Media Cards (optional)
      Using a 32 MB Smart Media card as expansion memory, you can store up to 60 files for the sampler and 5 groups of patch memory. Using a Smart Media reader/writer with a USB interface, Smart Media card can also be used as an interface between the 707II and your PC. You can back up data, as well as exchange patches and samples on the Internet.

REAR PANEL

















SPECIFICATIONS

Effect Type : 74
Effect Module : 8
Maximum Simultaneous Effects : 10
Patch Memory : 120 (User60+Preset60)
Sampling Frequency : 31.25kHz
A/D Conversion : 20bit 64times oversampling
D/A Conversion : 20bit 8times oversampling
Guitar Input : 1/4"Phone Jack x 1
Nominal Input Level : -20dBm
Input Impedance : 470k ohm
AUX Input : 1/8"Stereo phone jack x 1 (Nominal input level : -20dBm, input impedance : 20k ohm)
Output (Used as both line and headphone) : 1/4"Stereo phone jack x 1
Maximum Output Level : +3dBm (at load impedance 10k ohm or more)
Display : 6digit alphanumeric LED, 2digit 7segment LED, Pedal Assign LED x 7, Drive variation LED x 3, Module LED x 9
Maximum sampling time (without Smart Media) : 6seconds
Sampler playback speed : x 1, x 1/2, x 1/4
Preset rhythm pattern : 60
Power Requirement : AA size (LR6) Battery x 4 (Optional) , or AC Adaptor DC9V/300mA/Center Minus type (Optional, AD-0006 recommended)
Battery life : 11hours or more (Alkaline type)
Dimension : 249 (W) x 195 (D) x 57 (H) mm
Weight : 860g (without battery)
Optional accessory : Smart Media (16MB~128MB, 3.3V) , AD-0006, AA size Battery *0dBm=0.775Vrms

YOGA D727S DRUMSET MICROPHONES
DENOX DRUM KITS
TA-8370

SPECIFICATION
Element Dynamic
Polar Patern: Uni-directional
Frequency: 20Hz-10Khz
Sensitivity: -58dB +- 3dB (0dB=1V/Pa at 1Khz)
Output Impedance: 150 ohm +- 30% (at 1Khz)
Net Weight: 390 g

DIGITECH RP50 GUITAR EFFECT PROCESSOR

Meet the incredibly feature-packed RP50. Our engineers built the RP50 with the great tone and effects you expect from DigiTech®, including award-winning amp, cabinet and pick-up modeling and an arsenal of studio-quality effects. They didn't skimp on the processing either. The RP50 uses our AudioDNA™ DSP chip to ensure that both modeling and effects are world-class. Plus 24-bit A/D/A conversion so that no frequency response is lost between inputs and outputs.

And when we weren't looking, our engineers even snuck in a drum machine with 30 patterns and an easy-to-use 13-LED array tuner. Then we made sure that the RP50's user interface was so simple a drummer could operate it (well most drummers, anyway).


Features

    * 11 Amp Models
    * 20 Studio Quality Effects, up to 8 at once
    * Built-in drum machne with 30 patterns
    * 40 user, 40 Factory Presets
    * Expression pedal input for Whammy, Wah and Volume
    * 24-Bit analog digital converters
    * Easy-to-read LED Display
    * Chromatic Tuner
    * Stereo Output doubles as headphone jack
    * Battry or external power supply*

ROGERS DRUM SET

12" - 13" - 14" - 16" - 16" istanbul ve smryna ziller 7 parça ve tama twin pedal

TAMA IMPERIALSTAR DRUM SET
10" - 12" - 14" - 16" - 20"